The Chamber of Mazarbul - 3D printed

For all terrain based discussions.

Moderators: Rangers, Leaders

Villager
 
Posts: 22
Joined: Thu May 02, 2013 7:37 am
Location: Poland

The Chamber of Mazarbul - 3D printed

Sun Nov 30, 2014 3:15 pm

Hello :)

I would like to present to You my version of Mazarbul. It's all made on 3D printer in FDM technology in PLA material.

size of chamber (6 elements):
external size: 345x335mm
internal size: 245x245mm
hight: about 90mm


And photos of course:
Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image



More photos of 3D prints about LotR/Hobbit in my photobucket profile, and also on Polish site about Lotr/Hobbit:
http://www.mitril.pl/forum/viewtopic.php?t=15102&start=60&postdays=0&postorder=asc&highlight=

Feel free to ask about anything.

And the most important thing, project of this whole model, pillars from Moria and Amon Hen was made by my friend from mitril.pl - Marian :)
Last edited by puzi on Thu Dec 04, 2014 8:59 pm, edited 1 time in total.

User avatar
Standard Bearer
 
Posts: 2335
Joined: Mon Sep 14, 2009 7:47 am

Re: The Chamber of Mazarbul

Sun Nov 30, 2014 10:49 pm

Wow! 3D printers are really going to revolutionaise this hobby! This is amazing!

Villager
 
Posts: 22
Joined: Thu May 02, 2013 7:37 am
Location: Poland

Re: The Chamber of Mazarbul

Sun Nov 30, 2014 11:48 pm

Yes i have similar opinion about it.
And photos Amon Hen and the pillar from Moria (pillar hight: 180mm)

Image

Image

And small columns of Moria (size is similar to columns from GW in The Mines of Moria)

Image

Squire
 
Posts: 225
Joined: Thu Feb 07, 2013 7:46 pm

Re: The Chamber of Mazarbul

Mon Dec 01, 2014 8:12 am

The future is here.

User avatar
Standard Bearer
 
Posts: 2269
Joined: Sun Sep 20, 2009 7:47 pm
Location: Wanaka, Central Otago, New Zealand

Re: The Chamber of Mazarbul

Mon Dec 01, 2014 8:27 am

I'm not entirely certain, but I think there's a technique where you put a printed object in a sealed container with some acetone and heat it. It's supposed to remove the ridges visible from the print layers. Maybe you might look into it as those final two columns look like they could do with it. Nonetheless, fantastic use of the 3d printer technology. Makes me with I had access to it.
http://bdhobbymadness.blogspot.co.nz/

May the wind under your wings bear you to where the sun sails and the moon walks!

Villager
 
Posts: 22
Joined: Thu May 02, 2013 7:37 am
Location: Poland

Re: The Chamber of Mazarbul

Mon Dec 01, 2014 10:33 am

Well, last columns was printed only to check model. That's why the layers are so much visible - layer hight was 0,35mm - the biggest possible on my 3D printer. The thinest layer is about 0,05-0,06mm than the layers isn't so bad :)
Check this model - printed on the same printer in thin layer without any mechanical/chemical interventions on it.

https://www.facebook.com/1478977759049468/photos/a.1478978235716087.1073741825.1478977759049468/1478978265716084/?type=1&theater

Better? :D

User avatar
Standard Bearer
 
Posts: 2269
Joined: Sun Sep 20, 2009 7:47 pm
Location: Wanaka, Central Otago, New Zealand

Re: The Chamber of Mazarbul

Mon Dec 01, 2014 7:30 pm

Much :D lol.
http://bdhobbymadness.blogspot.co.nz/

May the wind under your wings bear you to where the sun sails and the moon walks!

Villager
 
Posts: 22
Joined: Thu May 02, 2013 7:37 am
Location: Poland

Re: The Chamber of Mazarbul - 3D printed

Tue Dec 16, 2014 10:47 pm

Photos of whole chamber :)
Finally.

Tomb and Gimly and goblins to show size of chamber.

Image

Image

Image

User avatar
Site Admin
 
Posts: 1038
Joined: Mon Sep 21, 2009 9:15 am

Re: The Chamber of Mazarbul - 3D printed

Wed Dec 17, 2014 3:05 pm

That's fantastic. Is it expensive to run?

Villager
 
Posts: 22
Joined: Thu May 02, 2013 7:37 am
Location: Poland

Re: The Chamber of Mazarbul - 3D printed

Wed Dec 17, 2014 3:36 pm

Well, time of printing is about 50 hours, printing price is about 10PLN - about 2 GPB - per hour.
So it depends, I think it is worth to have it to play on it :)
When I will finish painting of Amon Hen then i will be painting Mazarbul, so it will be ready to play, but i need to print it again becaus in this version there is no locks to put it together.
And then i think about printing those big columns to make whole battle table - but it will take a long time ;)

Next
Return to Terrain

Who is online

Users browsing this forum: No registered users and 2 guests